Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Ultramid® B3U42G6 - PA6-GF30 - BASF

Material Data Center offers the following functions for Ultramid® B3U42G6:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Ultramid B datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Processing/Physical Characteristicsdry / condUnitTest Standard
ISO Data
Melt volume-flow rate, MVR 40 / * cm³/10min ISO 1133
Temperature 275 / * °C -
Load 5 / * kg -
Molding shrinkage, parallel 0.2 / * % ISO 294-4, 2577
Molding shrinkage, normal 0.7 / * % ISO 294-4, 2577
Mechanical propertiesdry / condUnitTest Standard
ISO Data
Tensile Modulus 11000 / 7700 MPa ISO 527
Stress at break 140 / 95 MPa ISO 527
Strain at break 2.7 / 4.5 % ISO 527
Flexural modulus, 23°C 11000 / 7600 MPa ISO 178
Flexural strength 225 / 160 MPa ISO 178
Charpy impact strength, +23°C 60 / 60 kJ/m² ISO 179/1eU
Charpy impact strength, -30°C 55 / 50 kJ/m² ISO 179/1eU
Charpy notched impact strength, +23°C 8 / 10 kJ/m² ISO 179/1eA
Charpy notched impact strength, -30°C 7.5 / 7 kJ/m² ISO 179/1eA
Thermal propertiesdry / condUnitTest Standard
ISO Data
Melting temperature, 10°C/min 220 / * °C ISO 11357-1/-3
Temp. of deflection under load, 1.80 MPa 206 / * °C ISO 75-1/-2
Coeff. of linear therm. expansion, parallel 24 / * E-6/K ISO 11359-1/-2
Coeff. of linear therm. expansion, normal 82 / * E-6/K ISO 11359-1/-2
Burning behav. at 1.5 mm nom. thickn. V-0 / * class IEC 60695-11-10
Thickness tested 1.5 / * mm -
Yellow Card available yes / * - -
Burning behav. at thickness h V-0 / * class IEC 60695-11-10
Thickness tested 0.4 / * mm -
Yellow Card available yes / * - -
Burning behav. 5V at thickness h 5VA / * class IEC 60695-11-20
Thickness tested 1.5 / * mm -
Yellow Card available yes / * - -
Glow Wire Flammability Index (GWFI) 960 °C IEC 60695-2-12
GWFI - thickness tested (1) 0.75 mm -
Glow Wire Flammability Index (GWFI) 960 °C IEC 60695-2-12
GWFI - thickness tested (2) 1.5 mm -
Glow Wire Flammability Index (GWFI) 960 °C IEC 60695-2-12
GWFI - thickness tested (3) 3 mm -
Glow Wire Ignition Temperature (GWIT) 800 °C IEC 60695-2-13
GWIT - thickness tested (1) 0.75 mm -
Glow Wire Ignition Temperature (GWIT) 800 °C IEC 60695-2-13
GWIT - thickness tested (2) 1.5 mm -
Glow Wire Ignition Temperature (GWIT) 825 °C IEC 60695-2-13
GWIT - thickness tested (3) 3 mm -
Electrical propertiesdry / condUnitTest Standard
ISO Data
Relative permittivity, 1MHz 3.8 / 4.4 - IEC 62631-2-1
Dissipation factor, 1MHz 170 / 640 E-4 IEC 62631-2-1
Volume resistivity 1E12 / 1E10 Ohm*m IEC 62631-3-1
Surface resistivity * / 1E14 Ohm IEC 62631-3-2
Electric strength 40 / 35 kV/mm IEC 60243-1
Comparative tracking index - / 600 - IEC 60112
Other propertiesdry / condUnitTest Standard
Water absorption 5.3 / * % Sim. to ISO 62
Humidity absorption 1.9 / * % Sim. to ISO 62
Density 1450 / - kg/m³ ISO 1183
Bulk density 700 kg/m³ -
Material specific propertiesdry / condUnitTest Standard
ISO Data
Viscosity number 120 / * cm³/g ISO 307, 1157, 1628
Processing Recommendation Injection MoldingValueUnitTest Standard
Melt temperature 270 - 290 °C -
Mold temperature 70 - 90 °C -
Processing Recommendation ExtrusionValueUnitTest Standard
Melt temperature 270 - 290 °C -
Characteristics
Processing
Injection Molding, Other Extrusion
Delivery form
Pellets
Additives
Flame retarding agent
Special Characteristics
Flame retardant, Halogen-free
Applications
Electrical and Electronical
Regional Availability
North America, Europe
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.